Electricians · Revere, MA

Electricians in Revere, Massachusetts

Compare contractors serving Revere, Suffolk County — call them directly, or send one request and let qualified pros come to you.

50 contractors serving Revere — including 3 based in town.

Contractors serving Revere

Electricians in Revere — what to know

Rebates & incentives

Revere is in Eversource electric territory, so homeowners qualify for Mass Save. The electrical work isn't directly rebated, but a 200A panel upgrade is typically the prerequisite for a Mass Save heat pump or heat-pump water heater, since an older 100A or fuse service can't carry the added load.

Given the 1960s–70s housing share, aluminum branch wiring shows up often and matters for safety and insurance separate from any rebate. For coastal homes, corroded meter sockets sometimes need replacement before new circuits are added. The panel work generally precedes the rebated heat-pump equipment.

Permits in Revere

Electrical work in Revere requires a permit under 527 CMR 12.00, the Massachusetts NEC amendments, and a licensed Journeyman or Master electrician. Permits are issued through the City of Revere's Inspectional Services Department, and a municipal wiring inspector inspects before energizing. Panel upgrades, meter-socket replacement, EV circuits, and rewires all need permits. Flood-zone properties near the beach may have added requirements for service-equipment placement, so confirm scope with your electrician up front.

Typical project cost

Inner Boston metro pricing applies in Revere, just under the city proper. A 100A-to-200A panel upgrade typically runs $2,700–$5,000; multi-family meter-bank work and weather-exposed mast relocations cost more. A Level 2 EV-charger circuit is generally $1,000–$2,200. Aluminum-branch remediation ranges from device-level pigtailing up to several thousand for broader work. A whole-home standby generator with transfer switch usually runs $8,500–$15,000 installed.

About Revere homes

Revere has about 23,311 housing units in Suffolk County, with a median home age around 65 years. The city blends dense older two- and three-families near Revere Beach and Beachmont with postwar and 1960s–70s single-families and multi-families in West Revere and the Point of Pines.

That mix means aluminum-branch remediation and 100A-to-200A upgrades in the mid-century stock sit alongside fuse-panel swaps and some knob-and-tube in the older near-beach homes. The coastal setting adds weather-exposed meter sockets and service masts to the common replacement list, and EV-charger demand is rising across the city.

Common questions — Electricians in Revere

Do beachfront Revere homes need special electrical work?
Sometimes. Weather-exposed meter sockets and service masts near Revere Beach and Point of Pines corrode faster and may need replacement, and flood-zone rules can affect service-equipment placement. An electrician should check before adding circuits.
Is Revere eligible for Mass Save rebates?
Yes. Revere is in Eversource territory, an investor-owned utility, so homeowners qualify for Mass Save. A 200A panel upgrade is usually the prerequisite before a rebated heat pump is installed.
My West Revere home from the 1970s has aluminum wiring. Is it safe?
Aluminum branch connections can loosen and overheat over time. A licensed electrician can remediate with approved connectors at devices or rewire affected circuits, which also helps with insurance underwriting.
Do I need a panel upgrade for a heat pump in Revere?
Often. Many Revere homes run 100A or fuse service that can't comfortably carry an air-source heat pump plus existing load. A 200A upgrade is typically the step that makes the Eversource/Mass Save heat-pump rebate workable.
Who inspects electrical work in Revere?
The City of Revere's Inspectional Services Department issues the permit under 527 CMR 12.00, and a municipal wiring inspector inspects before the work is energized. Your licensed electrician handles the permit.

Electricians contractors in nearby towns