Electricians · Medford, MA

Electricians in Medford, Massachusetts

Compare contractors serving Medford, Middlesex County — call them directly, or send one request and let qualified pros come to you.

50 contractors serving Medford — including 4 based in town.

Contractors serving Medford

Electricians in Medford — what to know

Rebates & incentives

Medford is in Eversource electric territory, so homeowners qualify for Mass Save. The electrical work isn't directly rebated, but a 200A panel upgrade is usually the gating step before a Mass Save heat pump or heat-pump water heater, since old fuse and 100A services can't carry the new equipment.

With a median home age around 83 years, knob-and-tube is widespread, and remediating it matters for insurance separate from any rebate. For two- and three-families, plan the service per unit so each dwelling has compliant capacity before following the heat-pump rebate path.

Permits in Medford

Electrical work in Medford requires a permit under 527 CMR 12.00, the Massachusetts NEC amendments, and a licensed Journeyman or Master electrician. Permits go through the City of Medford's Building Department / Inspectional Services, and a municipal wiring inspector inspects before energizing. Panel upgrades, meter-bank work, EV circuits, and rewires all need permits. Two- and three-family jobs often mean separate per-unit permits, so confirm scope with your electrician before starting to keep the inspection on track.

Typical project cost

Inner Boston metro pricing applies in Medford. A 100A-to-200A panel upgrade typically runs $2,800–$5,200; multi-family meter-bank rebuilds cost more. A Level 2 EV-charger circuit is generally $1,000–$2,300, with limited off-street parking complicating the run. Knob-and-tube rewiring is priced by access and often lands $7,500–$18,000 per unit. A whole-home standby generator with transfer switch usually runs $8,500–$15,000 installed.

About Medford homes

Medford has about 26,761 housing units in Middlesex County, with a median home age around 83 years. The city blends early-1900s Colonials and Victorians in West Medford and the Hillside with dense two- and three-family woodframes near Medford Square and South Medford, most wired generations ago on fuse panels and knob-and-tube.

That older stock makes service upgrades and rewiring the core of local electrical work. Two- and three-family meter-bank work is routine, the Tufts-adjacent rental areas keep device and circuit work steady, and knob-and-tube remediation driven by insurance is a recurring reason owners upgrade.

Common questions — Electricians in Medford

Is Medford eligible for Mass Save rebates?
Yes. Medford is in Eversource territory, an investor-owned utility, so homeowners qualify for Mass Save. A 200A panel upgrade is usually the prerequisite before a rebated heat pump or heat-pump water heater is installed.
My West Medford Colonial has knob-and-tube — should I rewire?
It's worth addressing. With the city's median home age around 83 years, active knob-and-tube is common and isn't rated for modern loads. Insurers may surcharge or decline it, so staged rewiring by a licensed electrician is typical.
Can each unit in my Medford three-family get its own panel?
Generally yes. Each dwelling unit needs adequate, code-compliant service, and many Medford two- and three-families run undersized fuse panels, so per-unit upgrades and meter-bank work are common before any heat-pump rebate.
Do I need a panel upgrade for a heat pump in Medford?
Usually. Old fuse or 100A service can't reliably carry an air-source heat pump plus existing load. A 200A upgrade is typically the step that makes the Eversource/Mass Save heat-pump rebate path workable.
Who inspects electrical work in Medford?
The City of Medford's building/inspectional services issues the permit under 527 CMR 12.00, and a municipal wiring inspector inspects before the work is energized. Your licensed electrician handles the permit.