Induction Range Wiring Cost in Massachusetts (2026): 30A, 40A, or 50A Circuit?

Induction range wiring in Massachusetts typically costs $400 to $900 for a 30A circuit, $600 to $1,200 for a 40A circuit, and $900 to $1,600 for a 50A circuit, all with the permit and inspection folded in. The hardware (breaker, wire, receptacle) is a small slice; the labor is the rest. The number that decides which row you land on is not the brand of range, it is the nameplate amperage on the back of the appliance and the distance from your panel to the kitchen.

Here is what nearly every quote gets wrong. Electricians default to a 50A circuit on 6 AWG copper with a NEMA 14-50 receptacle because that is what an electric range used to need in the resistance-coil days. A modern 30-inch induction slide-in from GE Profile, Bosch, or Samsung calls for 40A on its nameplate, and a 30-inch induction cooktop (no oven) often only calls for 30A. Pulling 6 AWG when 8 AWG would do is not unsafe, it is just more expensive, and in a tight 100-amp Massachusetts panel it can push you toward a service upgrade you do not actually need. For the wider picture on residential electrical work, the electricians hub is the place to start.

How much does induction range wiring cost in Massachusetts?

Induction range wiring in Massachusetts runs $400 to $1,600 installed, depending on the circuit size, the wire run, and whether your panel has a free double-pole breaker slot. The table below is the honest spread by scenario for the wiring alone (it does not include the range itself, which is a separate $1,500 to $4,500 purchase, or a panel upgrade if one is triggered).

Circuit	Typical wire	Common appliance fit	Installed cost in MA	What you are paying for
30A, 240V	8 AWG copper (10 AWG for 30A is generally undersized for continuous range loads, use 8)	Induction cooktop, no oven; some compact slide-ins	$400 – $900	Breaker, wire, receptacle or hardwire, short run, permit, inspection
40A, 240V	8 AWG copper	Most 30-inch induction slide-in ranges (GE Profile, Bosch 800, Samsung NE63T)	$600 – $1,200	Same, with a 40A double-pole breaker and a typical 15 to 40 ft run
50A, 240V	6 AWG copper	36-inch ranges, dual-fuel pro models, or "future-proof" installs	$900 – $1,600	Heavier wire, often a longer or in-wall fished run, NEMA 14-50 receptacle
With 100A to 200A panel upgrade	n/a	Triggered when your panel has no spare capacity	wiring job + $2,500 to $6,000	A whole new service, meter, mast, utility coordination

A few things to read out of that table. The 30A and 40A circuits use the same 8 AWG wire, so the price gap is mostly the breaker and a slightly bigger receptacle if it is a plug-in install. The jump to 50A is real, 6 AWG copper is materially more expensive per foot, harder to pull through a finished wall, and it terminates in a NEMA 14-50 that requires GFCI protection under the current code. If a contractor wants to install a 50A circuit for a range whose nameplate says 40A, ask them why. The honest answer is usually "that is what we always do," which is not the same as "that is what your appliance needs." A standalone panel upgrade in Massachusetts is its own cost world, do not let it get bundled into a wiring quote without itemization.

What size circuit does an induction range actually need?

Read the nameplate on the back of your specific range, then size the circuit at 125% of that nameplate amperage and round up to a standard breaker. For most 30-inch induction slide-ins sold in 2026 the answer is a 40A circuit on 8 AWG copper. Many induction cooktops (the cooktop only, with no oven below) call for 30A. Only the 36-inch and pro-style ranges genuinely need 50A.

Some real nameplates we pulled from manufacturer spec sheets:

• GE Profile 30" slide-in induction range (PHS930YPFS family): 40A at 240V, 12.5 kW.
• Bosch 800 Series 30" induction slide-in range (HII8056U): 40A at 240V, 14 kW.
• Samsung 30" slide-in induction range (NE63T): 40A at 240V, ships with a 50A-rated cord because cords are sold to fit a 50A receptacle, the circuit breaker still sizes to 40A.
• Bosch 800 Series 30" induction cooktop (NIT8060UC): 30A at 208 to 240V, 7.2 kW. (Cooktop only, no oven.)

That last bullet is the one people miss. The cord that comes in the box is a 50A 4-wire cord because the appliance industry standardized the cord, not because the appliance pulls 50 amps. The breaker, the wire, and the receptacle all size to the nameplate, not the cord. The Massachusetts Electrical Code (527 CMR 12.00) adopts NFPA 70, the National Electrical Code, which is explicit on this: branch-circuit overcurrent protection follows the appliance nameplate plus the 125% continuous-load rule, not whatever receptacle happens to be on the cord.

A note for nervous remodelers, NEC 220.55 lets a service-load calculation treat one household range of 12 kW or less as an 8 kW demand. That is a feeder/service calculation, not a branch-circuit rule, but it is the reason a 200A panel almost never runs out of capacity for an induction range. The drama is at the branch circuit, not the service.

Will switching from gas to induction trigger a panel upgrade?

Usually not in a 200A house, sometimes in a 100A house. The honest test is a load calculation by a licensed electrician (NEC 220.82 covers the optional dwelling method). If your existing panel has a free double-pole 40A slot and the load calc shows headroom, you keep the panel and run a new circuit, and the wiring job stays in the $600 to $1,200 column.

The houses that get squeezed are old Massachusetts 100A services already feeding an electric dryer, an electric water heater, and a recently installed heat pump. Add an induction range and the math gets tight. That is where the 100A-to-200A upgrade enters the conversation, and at that point your range project is no longer a range project, it is a service project. The same logic comes up on the heat pump side, and does a heat pump need a panel upgrade in Massachusetts walks through that decision in detail.

Here is the practical takeaway. If your panel is borderline, sizing the induction circuit to the nameplate (40A, not 50A) can keep you under the line. A 40A induction circuit is 8 kW of demand under NEC 220.55; a "future-proofed" 50A circuit is treated the same in the service calc but it is more expensive to install, and the larger physical breaker can be the straw that breaks an already-stuffed panel's back. Match the circuit to the appliance, then handle the panel question on its own merits.

Hardwire or NEMA 14-50: which for an induction range?

For a slide-in range that lives permanently in a kitchen base cabinet, NEMA 14-50 (or NEMA 14-30 on a 30A circuit) is fine and is what almost every installer does, because the range needs to be pulled out for service. Hardwiring is the right call for a built-in cooktop (because there is nothing to pull out) and for any installation where the range cord would sit in a wet or floor-level area.

The trap is mismatched receptacles. A 40A circuit on 8 AWG should land on a NEMA 14-30 receptacle if there is one available, or be hardwired. Many electricians install a 50A receptacle (NEMA 14-50) on a 40A circuit because the appliance cord plug fits 14-50 only. That is permitted by NEC for ranges (the receptacle can be one size larger than the circuit it serves on a range branch), but you should know it is happening, and it is part of why your kitchen ends up with a 50A-shaped outlet on a 40A circuit. None of that is wrong, just understand that the outlet face is not telling you the breaker size.

Under current code, a 14-50 receptacle in a kitchen also requires GFCI protection. That is a small added cost (a GFCI breaker is more than a standard breaker) and an occasional source of nuisance trips with some induction ranges, ask your electrician about brand-specific compatibility before they install one.

Do you need a permit and a licensed electrician in Massachusetts?

Yes. A new 240V branch circuit for a range requires an electrical permit from your city or town's Inspector of Wires, and the work must be performed or supervised by a Massachusetts-licensed electrician under 527 CMR 12.00, the Massachusetts Electrical Code that adopts NFPA 70 (the NEC). The 2023 edition is currently in force; the Board of Fire Prevention Regulations has approved the 2026 NFPA 70 amendments with an effective date of April 24, 2026, so any work that crosses that date will be inspected against the 2026 code.

Why this matters for your wallet: the permit and inspection are not paperwork theater. The inspector signs off that the breaker size, the wire gauge, the GFCI protection, and the receptacle type all match the nameplate. If you skip the permit and later list the house, an alert buyer's inspector will flag the unpermitted kitchen wiring, and the resale headache is worse than the permit fee. Mass Save also generally requires installation by a licensed contractor for rebate eligibility (see the next section). For a deeper walk-through of the permit process, electrical permits in Massachusetts covers what to expect.

The Mass Save $500 induction stove rebate and what to skip

Mass Save offers a $500 rebate to Massachusetts residential customers who replace an existing natural gas or propane stove with an ENERGY STAR certified induction range, on purchases made between January 1, 2026 and December 31, 2026 (per Mass Save's 2026 program). Applications must be postmarked or submitted online by February 28, 2027. The rebate is for the appliance, not the wiring, but it materially changes the net cost of going gas-to-induction.

The fine print, all from masssave.com:

• You must be a residential customer of Berkshire Gas, Cape Light Compact, Eversource, Liberty, National Grid, or Unitil. If you live in one of Massachusetts' Municipal Light Plant (MLP) towns (Concord, Belmont, Braintree, Wellesley, Reading, and others), you are not a Mass Save customer and this rebate does not apply, your local MLP may have its own appliance program.
• The existing gas or propane stove must be verified before removal (keep a dated photo).
• The induction range must be new and ENERGY STAR certified.
• One rebate per account.

What to skip, the federal Energy Efficient Home Improvement Credit (IRS 25C) expired December 31, 2025 under the One Big Beautiful Bill (enacted July 2025). Any blog post telling you to claim 25C for an induction range installed in 2026 is outdated, the property must have been placed in service by the end of 2025. Massachusetts received roughly $73 million for the Home Electrification and Appliance Rebates (HEAR / HEEHRA) program from the IRA, which DOER is administering, but as of mid-2026 the consumer-facing portal had not opened with a specific induction-range payout amount. Watch the mass.gov Energy Rebates page, do not bank on a number that has not been published.

So the honest 2026 math: Mass Save $500 if you are gas-to-induction and on a Mass Save utility, and that is the whole confirmed-rebate picture for an induction range right now.

What a fair induction range wiring quote looks like in Massachusetts

A fair quote names the circuit size in amps, the wire gauge, whether the install is hardwired or plug-in, and itemizes the permit and inspection separately from labor. It should also reference your range model (or the spec sheet you provided) so the breaker matches the nameplate.

Red flags to push back on:

• A blanket "50A circuit" with no reference to your range's nameplate. Defaulting to 50A on every job is the lazy way; it can be appropriate, it can also be a $300 to $500 unnecessary upcharge.
• A quote that lumps a service upgrade into the wiring line item without breaking it out. A $4,500 "induction range install" hiding a panel upgrade is not a wiring price, it is two jobs.
• No permit fee on the quote. Permit and inspection are not optional in Massachusetts under 527 CMR 12.00.
• Pushing a NEMA 14-50 receptacle on a 30A or 40A circuit without explaining why (it is permitted on a range branch, but you should hear the reason).
• No mention of the Mass Save rebate paperwork. The rebate is a real $500, and the contractor should know how it works if they install induction ranges regularly.

Get two quotes from licensed Massachusetts electricians. If you are stacking other electrification (a heat pump, a future EV charger), tell them up front so the panel question is answered once instead of three times. EV charger installation cost in Massachusetts covers the same 240V territory from the car side, and the load-calc work overlaps almost entirely.

Frequently asked questions

What size breaker do I need for an induction range in Massachusetts? Read the nameplate on the back of your specific range and size the breaker at 125% of the nameplate amperage. For most 30-inch induction slide-ins (GE Profile, Bosch 800, Samsung NE63T) the answer is a 40A double-pole breaker on 8 AWG copper. Induction cooktops (no oven) are often 30A. Only 36-inch and pro-style ranges genuinely need 50A.

Does an induction range need a 50 amp circuit? Usually no. The 50A / 6 AWG / NEMA 14-50 setup is a holdover from older electric ranges with resistance coils. Modern 30-inch induction ranges from GE Profile, Bosch, and Samsung have 40A nameplates and run cleanly on 8 AWG copper.

How much does it cost to install a 240V outlet for an induction stove in Massachusetts? Roughly $400 to $900 for a 30A circuit, $600 to $1,200 for a 40A circuit, and $900 to $1,600 for a 50A circuit, all installed with the permit and inspection. A panel upgrade, if your service is undersized, adds $2,500 to $6,000 on top.

Do I need a permit to install a 240V circuit in Massachusetts? Yes. A new branch circuit requires an electrical permit pulled by a licensed Massachusetts electrician from your local Inspector of Wires, with an inspection before the wiring is covered, under 527 CMR 12.00.

Will switching from gas to induction trigger a panel upgrade? Not usually in a 200A house. In an older 100A service already running an electric dryer, an electric water heater, and a heat pump, the load calculation might push you to 200A. Sizing the induction circuit to its true nameplate (40A, not 50A) helps keep tight panels under the line.

Is there a Massachusetts rebate for switching from a gas stove to an induction range? Yes. Mass Save offers a $500 rebate for replacing a natural gas or propane stove with an ENERGY STAR certified induction range on purchases between January 1 and December 31, 2026, for residential customers of Berkshire Gas, Cape Light Compact, Eversource, Liberty, National Grid, or Unitil. MLP-town residents are not eligible. The federal 25C credit expired December 31, 2025 and does not apply to 2026 work.

Ready to wire your induction range?

If you have picked your range (or are about to) and want a real quote that sizes the circuit to your specific nameplate, get matched with licensed Massachusetts electricians who handle induction range wiring and the Mass Save rebate paperwork. Bring the model number; the right answer starts there.